Acoustic emission as an information factor of dissipative processes in metal cutting
Authors: Yakubov Ch.F., Kim V.A., Bashkov O.V., Komkova T.Yu.
Published in issue: #8(104)/2020
DOI: 10.18698/2308-6033-2020-8-2011
Category: Metallurgy and Science of Materials | Chapter: Metal Science, Thermal Processing of Metals and Alloys
The paper focuses on the issues of using acoustic emission signals as information characteristics of dissipative cutting processes. We analyzed time dependences of the root-mean-square values of the amplitudes (RMS) and energy-frequency distributions of the acoustic signals of the cutting process. Furthermore, we identified the ranges of frequencies, amplitudes and energies of acoustic waves, responsible for individual dissipative mechanisms of the cutting process. Findings of research show that technological media, depending on the composition and thermophysical properties, have a different effect on the processes of plastic deformation and fracture during cutting, which directly affect the energy-frequency distribution of the acoustic emission signal. We have come to a conclusion that, irrespective of the lubricating and cooling technological media used, the energy of acoustic signals, when cutting at a speed of 50 m / min, is 2.0‒2.5 orders of magnitude higher than when cutting at a speed of 75 m / min, which indicates a wider range of acoustic emission sources; in this case, the composition of the cooling lubricants significantly affects the energy of acoustic waves.
References
[1] Kim V.A., Mokritsky B.Ya., Yakubov Ch.F. Analysis of the shear plane during chip formation during the cutting process. Part 1. Metalloobrabotka [Metalworking], 2019, no. 2 (110), pp. 9‒14.
[2] Kim V.A., Mokritsky B.Ya., Yakubov Ch.F. Analysis of the shear plane during chip formation during the cutting process. Part 2. Metalloobrabotka [Metalworking], 2019, no. 2 (110), pp. 15‒21.
[3] Kishi T., Kuribayashi K. Acoustic emission in the process of plastic deformation and its interpretation. Kinzoku, 1977, vol. 47, no. 7, pp. 67–72.
[4] Bhaskaran J., Murugan M., Balashanmugam N., Chellamalai M. Monitoring of hard turning using acoustic emission signal. Journal of Mechanical Science and Technology, 2012, no. 26 (2), pp. 609‒615.
[5] Marasanov V.V., Sharko A.A., Koberskiy V.V. VISNIK KhNTU (Bulletin of KNTU), 2016, no. 2 (57), pp. 60‒65.
[6] Ivanov V.I. Dokl. AN SSSR ― Proceedings of the USSR Academy of Sciences, 1986, no. 287:2, pp. 302‒306.
[7] Gusev A.V., Zakuraev V.V., Turygin Yu.V. Intellektualnye sistemy v proizvodstve (Intelligent systems in manufacturing), 2013, no. 2 (22), pp. 49‒55.
[8] Blagoveshchenskiy V.V., Panin I.G. Fizika tverdogo tela ― Physics of the Solid State, 2017, vol. 59, no. 8, pp. 1554‒1556.
[9] Dornfeld D., Kannatey-Asibu E. Acoustic emission during orthogonal metal cutting. International Journal of Mechanical Sciences, 1980, no. 22, pp. 285‒296. DOI: 10.1016/0020-7403(80)90029-6
[10] Kim V.A., Mokritskiy B.Ya., Samar E.V., Yakubov Ch.F. Metalloobrabotka (Metalworking), 2017, no. 3 (99), pp. 2‒8.
[11] Kuznetsov V.D. Narosty pri rezanii i trenii [Cutting and friction build-up]. Moscow, GITTL Publ., 1956, 284 p.
[12] Semashko N.A., Shport V.I., Marin B.N., et al. Akusticheskaya emissiya v eksperimental’nom materialovedenii [Acoustic emission in experimental materials science]. Moscow, Mashinostroenie Publ., 2002, 240 p.
[13] Bashkov OV, Panin S.V., Byakov A.V., et al. Stadiynost deformatsii polikristallicheskikh materialov. Issledovanie akustiko-ehmissionnym i optiko-televi-zionnym metodami [Stages of deformation of polycrystalline materials. Research by acoustic emission and optical-television methods]. Tomsk, National Research Tomsk Polytechnic University Publ., 2004, 301 p.
[14] Andrianov D.S., Blagoveshchensky V.V., Panin I.G. Zhurnal tekhnicheskoy fiziki ― Technical Physics, 2016, vol. 86, no. 5, pp. 124‒127.
[15] Kabaldin Yu.G., Kuzmishina A.M. Izvestiya vysshikh uchebnykh zavedeniy. Mashinostroenie ― BMSTU Journal of Mechanical Engineering, 2017, no. 7 (688), pp. 72‒80.