Experimental study of the nature of the load distribution on the turns of the thread of the planetary roller-screw mechanism
Authors: Ryakhovskiy O.A., Marokhin A.S., Vorobyev A.N., Khachirova O.A.
Published in issue: #12(96)/2019
DOI: 10.18698/2308-6033-2019-12-1940
Category: Mechanics | Chapter: Dynamics, Strength of Machines, Instruments, and Equipment
The article considers the effect of axial load on the turns of the thread of the planetary roller-screw converter of rotational motion into translational one. For this purpose an experimental setup was made in which the nut lies end-face on the flat surface of the press, a screw is screwed into it. The force is applied to the screw through a ball to distribute the load uniformly. The design of the machine for compression measurement allows automatic recording the axial mutual movement of tested mechanism parts when the loading force changes. Contact and displacement occur when the loading force reaches 300 N. The results are obtained in the form of a "force – displacement" graph. In the course of the experiment, the influence of step error on the uniformity of the contacts of the turns of the mating parts of the planetary roller-screw mechanism was checked. The results of the experiment are analyzed, the influence of inaccuracy of manufacturing thread of planetary roller-screw mechanism parts on its capacity for use in feed drives of various machines is considered.
References
[1] Morozov V.V. Rolikovintovye mekhanizmy. Kinematicheskie kharakteristiki [Roller screw mecanisms. Motion characteristics]. Vladimir, Vladimir State University Publ., 2005, 78 p.
[2] Sokolov P.A., Sorokin F.D., Ryakhovsky O.A., Blinov D.S., Laptev I.A. Vestnik MGTU im. N.E. Baumana. Ser. Mashinostroyeniye — Herald of the Bauman Moscow State Technical University. Series: Mechanical Engineering, 2006, no. 1, pp. 61–72.
[3] Blinov D.S., Morozov M.I. Izvestiya vysshikh uchebnykh zavedeniy. Mashinostroenie — Proceedings of Higher Educational Institutions. Маchine Building, 2013, no. 3, pp. 62–72.
[4] Ryakhovsky O.A., Sorokin, F.D., Marokhin A.S. Izvestiya vysshikh uchebnykh zavedeniy. Mashinostroenie — Proceedings of Higher Educational Institutions. Маchine Building, 2013, no. 11, pp. 12–19.
[5] Roller screws: SKF – PUB MT / P1 14489 EN, 2014, 140 p. Available at: https://www.skf.com/binary/82-153959/14489-EN-Roller-screw-catalogue.pdf
[6] Blinov D.S. Planetarnye rolikovintovye mekhanizmy. Konstruktsii, metody rashchetov [Planetary roller-screw mechanisms. Designs, methods of calculations]. Ryakhovsky O.A. ed., Moscow, BMSTU Publ., 2006, 222 p.
[7] Kozyrev V.V. Konstruktsii rolikovintovykh peredach i metodika ikh proektirovaniya [Structures of roller-screw drives and methods of their designing]. Vladimir, Vladimir State University Publ., 2004, 100 p.
[8] Ryakhovsky O.A., Blinov D.S., Pleshakov Yu.D., Sokolov P.A. Vestnik mashinostroeniya — Russian Engineering Research, 2000, no. 8, pp. 8–10.
[9] Sokolov P.A. Ratsionalnyy vybor prednatyaga v planetarnykh rolikovintovykh peredachakh s uchetom tochnosti izgotovleniya. Diss. cand. tekhn. nauk [Rational selection of preload in planetary roller-screw drives with due regard for manufacturing accuracy. Cand. eng. sc. diss.]. Moscow, 1997, 137 p.
[10] Blinov D.S., Zenkinа, Ya.P. Mashiny i ustanovki: proektirovanie, razrabotka i ekspluatatsiya — Machines and Plants: Design and Exploiting, 2017, no. 3, pp. 15–34. https://doi.org/10.24108/aplts.0317.0000069