68
ISSN 0236-3941. Вестник МГТУ им. Н.Э. Баумана. Сер. “Машиностроение”. 2012
30.
Stability limits of milling considering the flexibility of the workpiece and the
machine / U. Bravo, O. Altuzarra, L.N. López de Lacalle, J.A. Sánchez, F.J.
Campa
//
Int. J. of Machine Tools and Manufacture. – 2005. – Vol. 45. –
P. 1669–1680.
31.
Influence of material removal on the dynamic behaviour of thin-walled struc-
tures. Peripheral milling / V. Thevenot, L. Arnaud, G. Dessein, G. Gazenave-
Larroche // Machining Science and Technology. – 2006. – Vol. 10, no. 3. –
P. 275–287.
32.
Simulation of low rigidity part machining applied to thin-walled structures /
L. Arnaud, O. Gonzalo, S. Seguy, H. Jauregi, G. Peigne // Int. J. of Advanced
Manufacturing Technology. – 2011. – Vol. 54. – P. 479–488.
33.
Modeling regenerative workpiece vibrations in five-axis milling / K. Weinert,
P. Kersting, T. Surmann, D. Biermann // Prod. Eng. Res. Devel. – 2008. –
No. 2. – P. 255–260.
34.
K e r s t i n g P., B i e r m a n n D. Simulation concept for predicting workpiece
vibrations in five-axis milling // Machining Science and Technology. – 2009.
–
Vol. 13, no. 2. – P. 196 –209.
35.
B i e r m a n n D., K e r s t i n g P., S u r m a n n T. A general approach to simu-
lating workpiece vibrations during five-axis milling of turbine blades // CIRP
Annals. Manufacturing Technology. – 2010. – Vol. 59. – P. 125–128.
36.
B a t h e K. Finite element procedures
.
–
NJ: Prentice-Hall, Inc., 1996. –
1037
p.
37.
В о р о н о в С.А., К и с е л е в И.А., Н и к о л а е в С.М. Расчетно-экспери-
ментальная методика идентификации параметров модели механической
системы с помощью модального анализа: cб. тр. 5-й Междунар. конф.
«
Проблемы механики современных машин», Улан-Удэ, 26–30 июня
2012
г. – Улан-Удэ: Изд-во ВСГУТУ, 2012. – С. 96–100.
38.
V o r o n o v S., K i s e l e v I. Dynamics of flexible detail milling // Proc. of
the Inst. of Mech. Eng. Part K: Journal of Multi-body Dynamics. – 2011. –
Vol. 225, no. 3. – doi:10.1177/1464419311418735
39.
L e e P., A l t i n t a s Y. Prediction of ball-end milling forces from orthogonal
cutting data // Int. J. of Machine Tool and Manufacture. – 1996. –
Vol. 36 (9). – P. 1059–1072.
40.
B u d a k E., A l t i n t a s Y., A r m a r e g o E.J.A. Prediction of milling force
coefficients from orthogonal cutting data // ASME J. of Manuf. Sci. and Eng.
– 1996. –
Vol. 118(2). – P. 216–224.
41.
Calculation of the specific cutting coefficients and geometrical aspects in
sculptured surface machining / A. Lamikiz, L. N. Lopez de Lacalle, J. A.
Sanchez, U. Bravo // Machining Science and Technology. – 2005. – Vol. 9,
no. 3. – P. 411–436.
42.
V o e l c k e r H.B., H u n t W.A. The role of solid modeling in machining
process modeling and NC-verification // Technical Report 810195. SAE. –
1981.
43.
General geometric modeling approach for machining process simulation /
H. El-Mounayri, M.A. Elbestawi, A.D. Spence, S. Bedi // Int. J. Adv. Manuf.
Technol. – 1997. – Vol. 13. – P. 237–247.
44.
S p e n c e A.D., A l t i n t a s Y. A Solid modeller based milling process simu-
lation and planning system // Trans. ASME. – 1994. – Vol. 116. – P. 61–69.